The article following next involving Tools You Need to Install a New Bathtub is quite interesting. Check it out yourself and figure out what you think of it.
Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and place the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already gotten a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and product list should consist of the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the bathtub must wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet as well as the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind should be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about complications with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our excerpt about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to read our blog. Liked our post? Please share it. Help other people check it out. Thank you so much for taking the time to read it.
Make An Appointment